Ahoj,
Rád by som vám ukázať nejaké vykreslený obraz z auta. Urobil som aktualizovať a navrhovať niektoré časti modelu a ja som pracoval na kabíne teraz.
Tu sú obrázky:
Hi,
I would like to show you some rendered image from the car. I did update and design some parts of the model and I working on the cabin now.
Here are the images:
-G-
Nevieš kam dať 2% dane?. A čo tak prispieť na chod našej najväčšej súťaže v Nitre?
Nevieš ako? Napíš správu Radkovi ( RKK) , on ti povie ako na to. Ďakujeme.
Nevieš ako? Napíš správu Radkovi ( RKK) , on ti povie ako na to. Ďakujeme.
GAZ-410 (GAZ-S-1) /Gabee/ 1:25
Moderátor: Oliver
- iconmaster | 35
- Last man standing
- Príspevky: 7433
- Meno: Peter Jankovič
- Bydlisko: Želiezovce
- Kontaktovať užívateľa:
Re: GAZ-410 (GAZ-S-1) /Gabee/ 1:25
Hello Gabesz,
nagyon jol halad a makett, ha megengeded lenne egy jo tanacsom: ha lekerekitett eleket / hengeres feluleteket csinalsz, sokat segit ha odafigyelsz a papir szaliranyara - sokkal konnyebb (es szebb is) ha a csavaras iranya a papir szaliranyara meroleges! A rajzlap es hasonlo A4 meretre vagott lapok szaliranya altalaban fuggoleges (tehat a hosszabb oldallal parhuzamos). Egyszeruen le is tudod ezt tesztelni, ha kivagsz egy negyzetet es megprobalod meghajlitani fuggoleges es vizszintes iranyban - amelyik iranyban nehezebben hajlik, arra mutatnak a szalak
Es hogy az iveknel maradjunk, bar nemtudom milyen modszerrel alakitod oket, nekunk bevalt modszer erre az alakitas valami fele erosebb hengeres targgyal (pl. acelrud, biciklikullo, stb.) puha alateten (nagyobb meretu radirgumi, egeralatet).
========
Ahoj Gabee,
velmi pekne ti ide stavba modelu, ak dovolis mal by jednu dobru radu: ak robis zaoblene / valcove plochy, je uzitocne si davat pozor na smer vlakien papiera - je totiz lahsie (aj krajsie) ak smer vlakien papiera bude kolmy na smer stacania. Smer vlakien papierov A4 je zvycajne zvisly (teda rovnobezny s dlhsou stranou). Mozes si to aj jednoducho otestovat, ak vystrihnes stvorec a pokusis sa ho ohnut v obidvoch smeroch - v ktorom smere sa tazsie ohyba, ten bude smer vlakien
A aby sme zostali pri oblukoch, sice neviem akym sposobom ich tvarujes, u nas je osvedceny sposob tvarovat nejakym pevnym valcovym predmetom (napr. ocelova tyc, vyplet z kolesa,..) na makkej podlozke (guma, podlozka pod mys).
nagyon jol halad a makett, ha megengeded lenne egy jo tanacsom: ha lekerekitett eleket / hengeres feluleteket csinalsz, sokat segit ha odafigyelsz a papir szaliranyara - sokkal konnyebb (es szebb is) ha a csavaras iranya a papir szaliranyara meroleges! A rajzlap es hasonlo A4 meretre vagott lapok szaliranya altalaban fuggoleges (tehat a hosszabb oldallal parhuzamos). Egyszeruen le is tudod ezt tesztelni, ha kivagsz egy negyzetet es megprobalod meghajlitani fuggoleges es vizszintes iranyban - amelyik iranyban nehezebben hajlik, arra mutatnak a szalak
Es hogy az iveknel maradjunk, bar nemtudom milyen modszerrel alakitod oket, nekunk bevalt modszer erre az alakitas valami fele erosebb hengeres targgyal (pl. acelrud, biciklikullo, stb.) puha alateten (nagyobb meretu radirgumi, egeralatet).
========
Ahoj Gabee,
velmi pekne ti ide stavba modelu, ak dovolis mal by jednu dobru radu: ak robis zaoblene / valcove plochy, je uzitocne si davat pozor na smer vlakien papiera - je totiz lahsie (aj krajsie) ak smer vlakien papiera bude kolmy na smer stacania. Smer vlakien papierov A4 je zvycajne zvisly (teda rovnobezny s dlhsou stranou). Mozes si to aj jednoducho otestovat, ak vystrihnes stvorec a pokusis sa ho ohnut v obidvoch smeroch - v ktorom smere sa tazsie ohyba, ten bude smer vlakien
A aby sme zostali pri oblukoch, sice neviem akym sposobom ich tvarujes, u nas je osvedceny sposob tvarovat nejakym pevnym valcovym predmetom (napr. ocelova tyc, vyplet z kolesa,..) na makkej podlozke (guma, podlozka pod mys).
Re: GAZ-410 (GAZ-S-1) /Gabee/ 1:25
Hi all. I am a testbuilder this modell. Thanks for your help iconmaster, you are right, the seat is not perfect, but this is not a final version. We are still beginners designer/testbuilder. Some components are not only make once, if wrong, build again and again, and after painted. I hope, the final look of flawless. When it is completely finished, surely you can see in any modelshow.
papermodelers.hu moderator
Re: GAZ-410 (GAZ-S-1) /Gabee/ 1:25
Ahoj,
@iconmaster:
Köszi az elismerő szavakat! Semmi probléma az észrevétellel, mivel nem én csinálom a tesztépítést... na de félretéve a tréfát, mint ahogyan János is leírta ez csak egy próba volt. A szálirányra nem igazán figyeltem eddig, de most, hogy említetted megpróbálok figyelni rá, így talán Jánosnak is könnyebb dolga lesz...
Vďaka za slová uznania! Žiadny problém s komentármi, pretože ja nerobím test stavať ... : Haha: Ale srandu stranou, ako John tiež písal, že to bol test. S obilím, a to naozaj pozor tak ďaleko, ale teraz keď si to spomenul sa snažím venovať pozornosť, takže možno John bude jednoduchšie urobiť ...
Po veľkom tichu, som tu zase! Urobil som prácu na kabíne! Bol to veľký projekt, pretože dvere a čelné sklo bude pohyblivá! Preto štruktúra kabíny bude musieť veľmi silné! Snažil som sa navrhnúť dobrý konštrukciu, ale je to trochu ťažké. Takže ... budeme vidieť na teste stavať. Začal som "odvíjať" projekt teraz. Čoskoro príde na fotky testu zostavenie.
Tu sú niektoré obrázky z 3D modelu:
After a big silence, I'm here again! I did work on the cabin! It was a big project because the doors and windshield will be movable! Therefore the structure of the cabin will be need very strong! I did try to design a good construction, but it is a little bit difficult. So... we will be see on the test build. I started the "unfold" project now. Soon to come the photos of the test build.
Here are some images from the 3D model:
-G-
@iconmaster:
Köszi az elismerő szavakat! Semmi probléma az észrevétellel, mivel nem én csinálom a tesztépítést... na de félretéve a tréfát, mint ahogyan János is leírta ez csak egy próba volt. A szálirányra nem igazán figyeltem eddig, de most, hogy említetted megpróbálok figyelni rá, így talán Jánosnak is könnyebb dolga lesz...
Vďaka za slová uznania! Žiadny problém s komentármi, pretože ja nerobím test stavať ... : Haha: Ale srandu stranou, ako John tiež písal, že to bol test. S obilím, a to naozaj pozor tak ďaleko, ale teraz keď si to spomenul sa snažím venovať pozornosť, takže možno John bude jednoduchšie urobiť ...
Po veľkom tichu, som tu zase! Urobil som prácu na kabíne! Bol to veľký projekt, pretože dvere a čelné sklo bude pohyblivá! Preto štruktúra kabíny bude musieť veľmi silné! Snažil som sa navrhnúť dobrý konštrukciu, ale je to trochu ťažké. Takže ... budeme vidieť na teste stavať. Začal som "odvíjať" projekt teraz. Čoskoro príde na fotky testu zostavenie.
Tu sú niektoré obrázky z 3D modelu:
After a big silence, I'm here again! I did work on the cabin! It was a big project because the doors and windshield will be movable! Therefore the structure of the cabin will be need very strong! I did try to design a good construction, but it is a little bit difficult. So... we will be see on the test build. I started the "unfold" project now. Soon to come the photos of the test build.
Here are some images from the 3D model:
-G-
Re: GAZ-410 (GAZ-S-1) /Gabee/ 1:25
Ahoj,
Som tu opäť s novými obrázkami. John je spustený testovacej verzie kabíny. Hlavnými zložkami sú pripravení a fit celkom dobre, ale existuje niekoľko dielov idú na to. Pre túto chvíľu bude len biele, ale neskôr maľoval. John robí základnou farbou teraz.
Som pracovať na kapotu a dvere.
Takže ... Tu sú niektoré obrázky ...
Hello Everybody,
I am here again with some new pictures. John is started the test build of the cabin. The main components are ready and fit quite well, but there are a few parts are going for it. For now only white, but later will be painted. John doing the primer paint now.
I working on the hood and the doors.
So... here are some images...
-G-
Som tu opäť s novými obrázkami. John je spustený testovacej verzie kabíny. Hlavnými zložkami sú pripravení a fit celkom dobre, ale existuje niekoľko dielov idú na to. Pre túto chvíľu bude len biele, ale neskôr maľoval. John robí základnou farbou teraz.
Som pracovať na kapotu a dvere.
Takže ... Tu sú niektoré obrázky ...
Hello Everybody,
I am here again with some new pictures. John is started the test build of the cabin. The main components are ready and fit quite well, but there are a few parts are going for it. For now only white, but later will be painted. John doing the primer paint now.
I working on the hood and the doors.
So... here are some images...
-G-
Re: GAZ-410 (GAZ-S-1) /Gabee/ 1:25
Gabee,
very nice work. When finished, will it be published or free to download?
Cus
M.
very nice work. When finished, will it be published or free to download?
Cus
M.
Teraz: Fordson F
Pred: Aero 500 Cililink, Rusnovy zdvihak, Snežný pluh,
Po(medzi): Miro mi uz nieco posle.
E-shop: http://www.papierovy-modelar.sk http://www.papershipwright.co.uk/
Pred: Aero 500 Cililink, Rusnovy zdvihak, Snežný pluh,
Po(medzi): Miro mi uz nieco posle.
E-shop: http://www.papierovy-modelar.sk http://www.papershipwright.co.uk/
Re: GAZ-410 (GAZ-S-1) /Gabee/ 1:25
@mimapnd@
Po prvé, ďakujem! Keď som sa dokončiť tento projekt, rád by som publikovanie ...
Môj testovací staviteľ John je (takmer) skončil farby. Lak chýba teraz a niektoré malé časti.
Tu sú niektoré nové obrázky:
@mimapnd@
First of all, thank you! When I will finish this truck project, I would like to publishing it...
My test builder John is (almost) finished the paint. The varnish is missing now and some little parts.
Here are some new images:
Po prvé, ďakujem! Keď som sa dokončiť tento projekt, rád by som publikovanie ...
Môj testovací staviteľ John je (takmer) skončil farby. Lak chýba teraz a niektoré malé časti.
Tu sú niektoré nové obrázky:
@mimapnd@
First of all, thank you! When I will finish this truck project, I would like to publishing it...
My test builder John is (almost) finished the paint. The varnish is missing now and some little parts.
Here are some new images:
Re: GAZ-410 (GAZ-S-1) /Gabee/ 1:25
mas to pekne spravene.fotky by si mohol nahravat rovno sem na forum.
Re: GAZ-410 (GAZ-S-1) /Gabee/ 1:25
@Roman@
Je nám ľúto, ale nechápal som, čo si písala. Snažila som preložiť s Google Translator, ale zlyhal.
Môžeš si to ešte raz znova?
Ďakujem vám!
Sorry but I did not understand, what you did write. I did try to translate with google translator but failed.
Can you read this once more again?
Thank you!
-G-
Je nám ľúto, ale nechápal som, čo si písala. Snažila som preložiť s Google Translator, ale zlyhal.
Môžeš si to ešte raz znova?
Ďakujem vám!
Sorry but I did not understand, what you did write. I did try to translate with google translator but failed.
Can you read this once more again?
Thank you!
-G-
Kto je prítomný
Užívatelia prezerajúci toto fórum: Žiadny pripojení užívatelia a 6 neregistrovaných